Side-Power SE130 Thruster, 24V
The SE130 is an excellent choice for yachts from 42-62' that desire a larger (10") tunnel for improved thrust, without the cost of counter-rotating props. The SE130's twin props generate up to 286 lb of thrust to easily maneuver large motor yachts in strong winds and heavy currents. Side-Power's wide range of control panels and remotes allow you to customize your SE130 installation to fit each application to the owner's personal specfications.
Specifications:
Thrust @ 21VDC | 286 lbs (130 kg) |
Thrust @ 24VDC | 352 lbs (160 kg) |
Approx. Boat Size | 42-62' (13-19 m) |
Power | 8.7 hp (6.5 kw) |
Tunnel Diameter (I.D.) | 9.8" (250 mm) |
Recommended Fuse Size | 325 Amps (SMANL325) |
Fuse Size | 325 Amp |
Minimum Battery Capacity | 760 CCA SAE |
Approximate Ship Weight (lbs) | 85 |
Features:
The gearhouse / drive legs of most Sleipner DC Electric thrusters are now fully galvanically isolated / separated from the electric motor and motor bracket. This ensures that even if there is an accidental short circuit or a current leak for other reasons, the immersed parts are not effected as they could be with direct electric contact.
- Achieved by composite bushings around the bolts and beneath the washers and a bushing in the motor bracket electrically isolating the drive housing from the motor bracket.
- Available on DC electric models with flexible couplers only, where the flexible coupler provides galvanic separation of the motor and gearleg shaft.
Sealed drive lubrication
Sealed gearleg with long-life "mechanical" seal where highly polished ceramic and carbon surfaces form the only moving sealing surfaces, ensuring protection against damaging water intrusion into the gear leg. Pre-filled with special gear oil for lifetime lubrication.
- "Mechanical" seals with surfaces of ceramic and carbon for ultimate security against water intrusion
Twin Propellers
Two counter-rotating propellers can give the most thrust at a good performance ratio in a minimal tunnel diameter. This system is used in our larger thrusters for maximum power. The TC models are the favourite thrusters among leading boatbuilders for their high-end yachts.
Q-propeller
The new 5 blade special skew propellers are the result of over 2 years of development work and thousands of tests. They have been designed to reduce the noise level, while maintaining the exceptional efficiency of the old 4 blade Sleipner propellers. This goal was achieved, and we even chose to make them a little bit more aggressive on some models, increasing the thrust on some thrusters about 5%. Please see individual information on each new thruster for more details.
- Noise reductions of up to 75% measured in controlled environments
- The expected and tested normal noise reduction in average installations: 20-40%
- Will be delivered on all Sleipner models except models with 300 mm and 385 mm tunnel diameter
- Upgrade kits are available for most SP series thrusters with special adaptors
Intelligent power control
The Sleipner unique thruster controller that intelligently protects the thruster from potential inherent problems in all high current applications as well as user faults. It includes several important safety features imperative in a product with such high power, run by DC electrics, as a thruster.
- Provides delay between drive directions
- Monitors solenoid functions to reduce the chance of solenoid lock-in
- Will stop the thruster in case of a lockedin solenoid, without extra user action and even without controlling a main switch.
Measurments:
Measurements | Value |
---|---|
(H) Height | 398mm / 15.67in |
(L) Length | 250mm / 9.84in |
(W) Width | 277mm / 10.91in |
(ID) Internal Diameter | 250mm / 9.84in |
(WD) Water Depth | 250mm / 9.84in |
(TL) Recommended Tunnel Length | 303mm / 11.93in |
(TL min.) Minimum Tunnel Length | 253mm / 9.96in |
(T min.) Minimum Tunnel Wall Thickness | 7mm / 0.28in |
(T max.) Maximum Tunnel Wall Thickness | 9mm / 0.35in |
Stern Measurements | Value |
---|---|
(L) Internal Length | 348mm / 13.7in |
(+L) Tunnel Length | 345mm / 13.6in |
(WD) Stern Water Depth | 250mm / 9.8in |
(HT) Maximum Hull Thickness | 55mm / 2.2in |